
Key Takeaway
Most tankless water heater problems come from a short list of causes: mineral scale in the heat exchanger, a blocked inlet filter, a flow rate too low to fire the burner, a venting or gas supply problem, or a failed part such as a flow sensor or igniter. Scale and filter problems are fixed with a flush and a clean. Sensor, igniter and fan failures are part replacements. Replacement makes sense when the heat exchanger is leaking or cracked, or when an older unit needs a costly part. SKS Plumbing repairs and replaces tankless water heaters across Hillsboro and Washington County, open seven days a week. Call (503) 319-9348.
Most tankless water heater problems come from a short list of causes: mineral scale inside the heat exchanger, a blocked inlet filter, a flow rate too low to fire the burner, a venting or gas supply problem, or a failed part such as a flow sensor or igniter. Scale and filter problems are fixed with a flush and a clean, failed parts are replaced, and the whole unit only needs replacing when the heat exchanger itself has failed or the repair costs more than the unit is worth.
This guide covers the symptoms Hillsboro, Beaverton and Portland homeowners call us about most, what causes each one, what a repair visit involves, and how to decide between repair and replacement.
How a Tankless Water Heater Works (and Why That Matters for Repairs)
A tankless water heater has no stored hot water. When you open a hot tap, a flow sensor detects water moving through the unit, the burner (or electric elements) fires, and the water is heated as it passes through the heat exchanger. According to the U.S. Department of Energy's overview of gas-fired tankless water heaters, these units "can provide hot water at a rate of 2 to 5 gallons per minute."
That design explains most failures. If the flow sensor cannot detect flow, the burner never fires. If scale narrows the heat exchanger, the water cannot pick up enough heat. If the venting or gas supply is restricted, the unit shuts itself down to protect itself and shows an error code. Knowing which part of the chain has stopped working is what a diagnosis is for.

Common Tankless Problems and What Causes Them
Hot water runs lukewarm or goes cold mid-shower
This is the most common call. The usual causes, from most to least likely:
- Scale in the heat exchanger. Minerals in the water coat the inside of the heat exchanger over time, which reduces how much heat reaches the water.
- A blocked inlet filter. Most units have a small screen where the cold water enters. Sediment collects there and cuts the flow.
- Too much demand at once. Two showers and the dishwasher together can ask for more hot water than a smaller unit can heat. This is a sizing issue rather than a fault.
- A failing flow sensor or mixing valve, which can make the temperature swing even when demand is normal.
No hot water at all
If the unit shows no sign of firing, check the obvious first: is the gas valve on, is the unit plugged in or the breaker on, and is there an error code on the display? Common causes we find are a failed igniter, a flame sensor that needs cleaning or replacing, a gas supply problem, or a flow sensor that no longer detects water moving. In freezing weather, a unit installed in a garage or on an outside wall can also be shut down by frozen pipes, which our frozen pipes guide covers.
An error code on the display
Every brand uses its own codes, so the number only tells you which area to look at: ignition, flame failure, venting, overheating or a sensor fault. The owner's manual lists them. Resetting the unit may clear a code for a day or two, but a code that keeps returning means something is wrong and needs to be found, not reset again.
Water leaking from the unit
A drip from a pipe connection or a pressure relief valve can usually be repaired. Water coming from inside the cabinet is more serious, because it can mean the heat exchanger is leaking. If you see water under the unit, shut off the water supply to it and call. A slow leak behind a wall-mounted unit can soak drywall for weeks before anyone notices, which is where leak detection helps confirm the extent.
Strange noises
Banging, whistling or a fan that sounds rough usually points to scale buildup or a fan motor wearing out. Neither is urgent on the first day, but both get worse.
Why Flushing (Descaling) Matters
Scale is the root cause behind many of the problems above, and it is the one that regular maintenance prevents. Navien, one of the major tankless manufacturers, says in its guide to descaling that it "recommends descaling a tankless water heater at least once a year," and warns that mineral buildup "can cause damage to your heat exchanger and may interfere with normal heating." Rheem gives similar advice in its maintenance guide: flush "about once a year," and more often where the water is hard.
A flush uses the service valves fitted below the unit. A small pump circulates a descaling solution through the heat exchanger, then the system is rinsed with clean water, the inlet filter is cleaned and the unit is tested. It takes about an hour. If a unit was installed without service valves, we can add them so future flushes are quick.
Water supply varies across our area. Hillsboro, Beaverton and Portland are served by different water providers, so mineral content is not the same everywhere. Your provider's annual water quality report lists hardness if you want to know how often your unit needs it. Once a year is a sensible minimum either way.

What a Tankless Repair Visit Involves
When you book a tankless water heater repair, the visit usually follows this order:
- 1Read the history. Most units store recent error codes. We check them before taking anything apart.
- 2Check supply and venting. Gas pressure, electrical supply, and the intake and exhaust vents. A blocked vent or an undersized gas line causes faults that look like a failed part.
- 3Test flow and temperature. We open fixtures to see whether the unit fires at a normal flow and how much temperature rise it delivers.
- 4Inspect the components. Inlet filter, flow sensor, igniter, flame sensor, fan and heat exchanger.
- 5Explain the options. You get the cause, the repair, and a written price before any work starts.
Gas lines, burners, venting and electrical components are work for a licensed plumber. Rheem's own guidance says tasks involving them "are best left to a licensed professional." The one job most homeowners can do safely is rinsing the inlet filter, if the manual explains how.
Repair or Replace a Tankless Water Heater?
Tankless units are built from replaceable parts, which is one reason they last longer than tank models. Our water heater installation and replacement page puts tankless lifespans at 15 to 20 years against 8 to 12 for a tank. So most faults are worth repairing. As a rough guide:
Usually a repair:
- Scale, a blocked filter or poor flow (flush and clean)
- A failed flow sensor, igniter, flame sensor, fan or thermistor
- A leaking connection or relief valve
- A venting or gas supply problem
Usually a replacement:
- A leaking or cracked heat exchanger
- An older unit that needs a circuit board or heat exchanger, where the part costs a large share of a new unit
- A unit that is too small for the household and runs cold whenever two fixtures are in use
- Parts no longer available for the model
If you are weighing a tankless unit against going back to a tank, our tank vs. tankless comparison covers the trade-offs, and our water heater repair or replace guide covers tank models.

What Affects the Cost of a Tankless Repair
We do not quote prices without seeing the unit, because the range is wide. These are the things that move it:
- The part. A flow sensor or igniter costs far less than a circuit board or heat exchanger.
- Brand and parts availability. Common parts are easy to get; parts for older or less common models can take longer.
- Whether a flush is needed too. Heavy scale is often behind a failed sensor, so the two are done together.
- Service valves. Adding them to a unit installed without them adds a little to the first visit and makes every future flush quicker.
- Venting or gas line work. If the cause is an undersized gas line or a vent problem, that is a separate fix from the unit itself.
Every SKS estimate is free and given in writing before work starts.
Book a Tankless Water Heater Repair
SKS Plumbing repairs, flushes and replaces tankless water heaters as part of our water heater installation and replacement service, in Hillsboro, Beaverton, Tigard, Portland and the rest of Washington County. We are licensed and insured, Oregon CCB #243571.
We are open seven days a week. Call (503) 319-9348, or book a visit for a free estimate.
Frequently Asked Questions
The most common causes are scale in the heat exchanger, a blocked inlet filter, or more hot water being drawn at once than the unit can heat. Running a second shower or the dishwasher at the same time can push a small unit past its limit. A flush and filter clean fixes the first two; a sizing problem needs a larger unit or a second one.
Each brand uses its own codes, so the code itself only points to an area: ignition, flame, venting, overheating or a sensor. The manual lists what each code means. Resetting the unit may clear it for a while, but a code that keeps coming back needs a plumber to find the cause.
Most manufacturers recommend descaling at least once a year, and more often where the water is hard. The flush runs a descaling solution through the heat exchanger with a small pump and takes about an hour.
Most faults are repairable because tankless units are built from replaceable parts: sensors, igniters, fans, valves and circuit boards. Replacement is usually the better choice when the heat exchanger is leaking or cracked, or when an older unit needs an expensive part.
Cleaning the inlet filter is a simple homeowner task if the manual covers it. Anything involving the gas line, burner, venting or electrical parts should be done by a licensed professional, because mistakes can cause gas leaks or carbon monoxide problems.



